This document is designed to provide Internode users with the Internode supported configurations for the Billion 6404 and 740x series of VoIP routers:

• The Billion 6404VP and 6404VGP are Ethernet VoIP routers, and used on Internode Wireless DSL broadband services.
• The Billion 7402VGP, 7401VGP-M, 7404VGP-M and 7404VGO-M are ADSL VoIP routers, and used on Internode ADSL and ADSL2+ broadband services.

When to use this guide

Please note that all Billion equipment sold by Internode is pre-configured. Hence in most cases, you should simply need to follow the connection process (step 1).

The rest of this guide may be useful when:

• you have performed a factory reset, and hence need to completely reconfigure the device (steps 2 to 5);
• you have purchased the device from someone else, and hence need the supported Internode configuration (steps 2 to 5);
• you are adding NodePhone to a device that you have previously purchased from Internode (steps 4 & 5);
• you wish to update the firmware (step 2); or
• you wish to change the NodePhone configuration - for example, so that all outbound calls are made via NodePhone in the case of Naked ADSL2+ services (step 2).

Step 1 : Connecting the Billion router

The first step when setting up your new 6404 or 740x is to ensure it is plugged in correctly.

1. Connect your phone line to the Line port on your ADSL splitter.
2. Connect a telephone cable from the ADSL Modem port on the ADSL splitter, to the ADSL port on the back of the router (740x series only).
3. Connect one end of the supplied Ethernet cable to the network card on your computer, and the other end to any of the LAN ports on the back of the router.
4. To enable NodePhone, connect your telephone handset or cordless telephone base station to the Phone 1 port.
5. To enable the 'failover & incoming PSTN calls' feature with NodePhone, connect a telephone cable from the Local Phone port on the splitter to the Line port on the back of the router. If you do not use this feature (eg because you have no analog telephone service), you must ensure that you set up your Billion with the 'VoIP Only' configuration - see Step 2.
6. Plug the power supply in to a 240V AC outlet and connect it to the back of the router.
7. Switch on the device.

Figure 1: Typical connection of the Billion 6404 and 740x series routers. Note the 6404 does not use the ADSL connection (Ethernet is used instead); and the 7401 has only one telephone port.

Step 2 : Firmware and Configuration

Follow this step if you wish to update the firmware, and/or change the NodePhone configuration file.

1. Start your web browser (eg Internet Explorer, Firefox, Safari) on your computer.
2. Enter 192.168.1.254 into the address bar, and press enter.
3. In the Username: field enter admin and in the Password: field enter admin. Please note that these are case sensitive.
4. The hardware type is listed as Model Name on the first page of the Billion configuration. If you're not sure, note down which model of Billion router you have.
5. If you need to upgrade your firmware, please find the instructions here to perform the firmware upgrade, and then return to this guide.
6. If you need to change your configuration file, please find the instructions here to download the configuration file, and then return to this guide.
7. Click on Configuration.
8. Click on System.
9. Click on Backup/Restore.
10. Click on Browse.
11. Select the configuration file that you downloaded, and open it.
12. Click on Restore. After the settings are saved press the restart the router and wait for the device to reboot.

Figure 2: Changing the Configuration file.

Step 3 : Entering your ADSL details

Follow this step to enter your Internode ADSL username and password.

1. Click on the Quick Start option on the left hand side menu.
2. Enter your username - in the form username@internode.on.net - into the Username field.
3. Enter your ADSL password into the Password field. The completed page is shown in Figure 3.
4. Press Apply at the bottom. This change takes effect immediately.

Figure 3: Entering your ADSL details.

Step 4 : Entering your NodePhone details

Follow this step to enter your Nodephone username and password, and select NodePhone as your VoIP service.

1. Click on the VoIP option on the left hand menu and choose the Wizard.
2. Select NodePhone from the SIP Service Provider dropdown.
3. Enter your NodePhone number in the Username and Phone Number fields.
4. Enter your password into the Password field.
5. Press Apply to save the changes. The correct settings are shown in Figure 4.
6. Press Apply, then Save Config. After the settings are saved press the restart the router and wait for the device to reboot.

Figure 4: Entering your NodePhone details.

Step 5 : Save and Reboot

Perform this step after you've made changes in steps 3 or 4.

1. Click on Save Config at the bottom of the configuration page.
2. Click Restart.
3. Be sure to select Restart with Current Settings when you reboot the device.

This completes the Billion configuration process for ADSL and NodePhone.

If you are having trouble setting up the wireless network, please see our wireless setup guides at here. If you have any further queries, please contact the helpdesk on 13 6633.

Additional Information

Enabling DTMF

Please refer to this page to enable DTMF on older Billion routers (sold by Internode prior to April 2007). DTMF is used to access the Nodephone2 Voicemail system, for example.

Advanced Users Only

If you're familiar with configuring your Billion, you may wish to manually set the dial plan information (instead of using our approved configuration files). These instructions are located here.